Lantac Tactical Competition Rifle

[Rburro2]

Grizzly- I assume there is a very limited market in the states for a straight pull AR, so how did you go about getting a straight pull upper and bolt sent over? Was that custom request from the manufacturer?

I didn't, I sourced and imported all the parts listed and built from the ground up.

Isn't that alextwogun's gun? Where did he go then? Is that one of them?

It is Alex's gun it's the exact same build spec that was posted on csr shooter and other forums.

[majordisorder]

It is Alex's gun it's the exact same build spec that was posted on csr shooter and other forums.

Yeah, but where's Alex? Who's this Grizzly dude? And why has he got (at least one of) Alex's gun?

[Sandgroper]

Yeah, but where's Alex? Who's this Grizzly dude? And why has he got (at least one of) Alex's gun?

No longer listed as a member and I can't find the original thread about his build.

Edit: Grizzley = Alextwoguns????

[Strangely Brown]

You could always build your own:

LAR Grizzly Lower
LAR OPS 4 Upper with BCG
Krieger .223 Wylde 1/7.7 SS bead blasted 16.5" barrel
Geissele SSA-E Trigger
Griffin Armament M4SD Muzzle Brake
Noveske NSR 11" Rail
Troy Industries Micro HK BUIS
JP LPK
Magpul UBR stock
Magpul Enhanced Rubber Butt Pad
Magpul MOE plus grip
Magpul Enhanced Trigger Guard
D&H Industries 20 round mag

Alex, did you manage to get it proofed?

Ps,
Love the new "non de plume"!

[Rburro2]

Doesn't it only need to be proofed if Alex intends to sell it?

[breacher]

Doesn't it only need to be proofed if Alex intends to sell it?

It ( or certain parts of it ) need to be proofed before it even reaches Alex / Grizzly

[Sandgroper]

Doesn't it only need to be proofed if Alex intends to sell it?

It ( or certain parts of it ) need to be proofed before it even reaches Alex / Grizzly

Chapter 24 of the HO Guidance covers proof of firearms and states:

24.3 The proving of firearms is governed by the Gun Barrel Proof Acts of 1868, 1950 and 1978 (However, note that much of the 1950 Act was repealed in 1996 by SI 1996/1576).
Under these Acts it is:
(a) an offence to sell, exchange, expose or keep for sale, or export, or keep for exportation, or to attempt to sell, exchange or export, or to pawn or pledge, or attempt to pawn or pledge, or to take in pawn or pledge, an arm, the barrels of which are not duly proved and marked as proved (section 108 and 109 of the 1868 Act);
(b) an offence to import into the United Kingdom small arms, the barrels of which are not duly proved and marked as proved, without giving notice in writing within seven days to either the London or Birmingham Proof House or to send such imported arms, within twenty-eight days of their arrival in the United Kingdom, to be proved at either the London or Birmingham Proof House (Section 122 of the 1868 Act).
This does not apply to any small arm imported by any person for their own personal use whilst it is in their possession. In such a case, the proof is the responsibility of the possessor.

[John MH]

It needs to be proofed if you use an RFD to accept and then pass on to you imported pressure bearing parts.

If comes direct to you for your own personal use then as above it does not need to be proofed, use a 3rd party and it does.

[Mattnall]

.
And except for Bob who does make there own.

Me.

A UK made lower, just being put in to production.

[alijnclarke]

I think I'm going to order a lantac tcr,, I did try to speak to Bradley arms but he doesn't seem that 'bothered about business'.

No doubt when I get on the phone I'll spend a lot more than I intended....